How To Set Up Frame Relay In Packet Tracer

Frame relay is a packet-switching protocol for connecting devices on a Wide Area Network (WAN). Here nosotros are going to show yous, how to configure Frame relay in Cisco routers using Cisco Parcel Tracker. The Frame relay originally designed for send beyond Integrated Services Digital Network (ISDN) infrastructure, it may be used today in the context of many other network interfaces. Read more than about Frame relay on Wikipedia.

Create your Lab within Cisco Packet Tracer or download Fram relay Lab which I have created for this commodity. Download CCNA Lab – Frame relay. This is not configured yet, but you must endeavour to configure information technology step past step co-ordinate to article.

How to Configure Frame Relay

ane. Open the Frame relay lab which you have downloaded and configure Frame relay the same equally screenshot.

Try to configure the serial interfaces of the Frame Relay switch like beneath screenshot.

two. On Serial0 of Frame relay switch add the following DLCI and named with router name or anything you want.

3. Add the DLCI 201 and named R1-R0 on Serial1 interfaces like the screenshot. Exercise the same for Serial2 and Serial3 interfaces, only modify the DLCI number 202, 203 and names R2-R0 and R3-R0.

4. Now configure frame relay like the screenshot. Don't miss configure, information technology will not work.

Configure Frame Relay - Technig — Configure Frame Relay – Technig

That's information technology, now try to configure R0 router and create three sub-interfaces for each router. If yous don't know to create sub-interface, endeavor to read inter VLAN routing article.

Configure R0:

Router>enable
Router#configure last
Enter configuration commands, i per line. Terminate with CNTL/Z.
Router(config)#hostname R0
R0(config)#interface serial 0/0/0
R0(config-if)#no shutdown
R0(config-if)#encapsulation frame-relay
R0(config-if)#leave

Create Sub-Interfaces:

R0(config)#interface serial 0/0/0.100 indicate-to-point
R0(config-subif)#ip address ten.x.10.1 255.255.255.252
R0(config-subif)#frame-relay interface-dlci 100
R0(config-subif)#go out
R0(config)#
R0(config)#interface series 0/0/0.101 Point-to-signal
R0(config-subif)#ip accost 10.10.10.5 255.255.255.252
R0(config-subif)#frame-relay interface-dlci 101
R0(config-subif)#leave
R0(config)#
R0(config)#interface serial 0/0/0.102 point-to-point
R0(config-subif)#ip address x.ten.10.9 255.255.255.252
R0(config-subif)#frame-relay interface-dlci 102
R0(config-subif)#exit
R0(config)#

Configure Router R1:

Router>enable
Router#configure terminal
Enter configuration commands, i per line. Terminate with CNTL/Z.
Router(config)#hostname R1
R1(config)#interface serial 0/0/0
R1(config-if)#no shutdown
R1(config-if)#encapsulation frame-relay
R1(config-if)#exit
R1(config)#
R1(config)#interface serial 0/0/0.200 indicate-to-bespeak
R1(config-subif)#ip address 10.10.10.2 255.255.255.252
R1(config-subif)#frame-relay interface-dlci 200
R1(config-subif)#exit
R1(config)#

Configure Router R2:

Router>enable
Router#configure concluding
Enter configuration commands, 1 per line. End with CNTL/Z.
Router(config)#hostname R2
R2(config)#interface serial 0/0/0
R2(config-if)#no shutdown
R2(config-if)#encapsulation frame-relay
R2(config-if)#exit
R2(config)#
R2(config)#interface series 0/0/0.201 point-to-point
R2(config-subif)#ip address 10.10.10.6 255.255.255.252
R2(config-subif)#frame-relay interface-dlci 201
R2(config-subif)#exit

Configure Router R3:

Router>enable
Router#configure terminal
Enter configuration commands, one per line. Terminate with CNTL/Z.
Router(config)#hostname R3
R3(config)#interface series 0/0/0
R3(config-if)#no shutdown
R3(config-if)#encapsulation frame-relay
R3(config-if)#exit
R3(config)#
R3(config)#interface series 0/0/0.300 betoken-to-point
R3(config-subif)#ip address x.x.10.10 255.255.255.252
R3(config-subif)#frame-relay interface-dlci 300
R3(config-subif)#go out
R3(config)#

The configuration is completed successfully.

Effort to configure the router 1, 2 and 3 with static routing or Rip Routing in society to communicate with each others.

If your lab won't piece of work correctly, download the configured frame relay Lab which piece of work perfectly and troubleshoot frame relay. In case of any problem regarding to Fram Relay configuration on Cisco devices, ask your question through comment.

Related Search:

frame relay example
how to configure frame relay in packet tracer
what is frame relay cisco
configure frame relay switch
frame relay configuration commands
frame relay point to multipoint
frame relay configuration point to point
frame relay configuration betoken to multipoint
frame relay configuration in gns3
frame relay cisco tutorial